M7 Maintenance Practices Sub-Module No 10 (Quiz No:1)

Spring

Quiz

 

1. Those springs that are in exposed areas can become --------- over time ?
   1.   Corroded
   2.   Fatigue strength
   3.   Overheated
2. Those springs in areas of high temperature can become -------------?
   1.   Fatigue strength
   2.   Overheated
   3.   Corroded
3. ----------- occurs on static springs and reduces the capacity of the loads that the spring can carry ?
   1.   Overheating
   2.   Fatigue strength
   3.   Corrosion
4. The other check, usually completed in a workshop environment, is the check ?
   1.   Load/deflection
   2.   Static measurement
   3.   Deflection
5. A special test rig is used, to load the spring with a --------------?
   1.   Compressive
   2.   Tensile
   3.   Compressive/Tensile
6. A meter on the rig will display the------------------ figures ?
   1.   Load vs deflection
   2.   Load
   3.   Deflection
7. When ------------ is detected, it must be assumed that the spring is not suitable for the designed task ?
   1.   Static Measurement
   2.   Corrosion
   3.   Overheating
8. When a spring carrying a -------- becomes corroded, the combination of fatigue and corrosion results in a serious loss of fatigue strength ?
   1.   Radial loads
   2.   Cyclic load
   3.   Axial loads
9. If a spring fails in any checks it is simply------------------?
   1.   Repair
   2.   Return to service
   3.   Replaced
10. The most common check, done on coil springs is on its ----------------?
    1.   Load
    2.   Static measurement
    3.   Load/deflection

Read More

M7 Maintenance Practices Sub-Module No 9 (Quiz No:1)

Pipes and Hoses

Quiz

 

1. To lessen the possibility of the pipe, wall kinking when it is being bent, it may be filled with a….., Which can be removed after the bending operation ?
   1.   Same metal alloy
   2.   Special unfuseable alloy
   3.   Special fusible alloy
2. Before filling the pipe with fusible alloy ,the pipe shouls be ……... First ?
   1.   Oiled
   2.   Greased
   3.   Dyed
3. After bending, the pipe should be unloaded from fusible alloy, by immersing it in………. Until all the alloy has run out ?
   1.   Cool water
   2.   Boiling water
   3.   Oven
4. A new piece of tubing should be cut approximately …..Than the tube to be replaced to provide for minor variations in bending?
   1.   10 percent longer
   2.   10 percent shorter
   3.   Equal to
5. If a tube cutter is not available, or if tubing of hard material is to be cut, use a fine-tooth hacksaw, preferably one having…….?
   1.   12 teeth per inch
   2.   32 teeth per inch
   3.   132 teeth per inch
6. A small amount of flattening in bends is acceptable, but the small diameter of the flattened portion must not be less than ………..Of the original outside diameter ?
   1.   75 percent
   2.   25 percent
   3.   57 percent
7. Bore test done with ……..., By use of a ball bearing being rolled in both directions through the hose ?
   1.   Flexible pipes
   2.   Loose pipes
   3.   Rigid pipes
8. The diameter of the ball should be……….. Of the internal diameter of the hose’s end fittings ?
   1.   90%
   2.   60%
   3.   30%
9. The AGS system uses a…... Flare ?
   1.   74 deg
   2.   32 deg
   3.   25 deg
10. The AN system uses flares of……... Flare ?
    1.   32 deg
    2.   25 deg
    3.   74 deg

Read More