Module -7 Final Practice Exam (Maintenance Practices 80 Questions 100 Mints)

 

Module -7 (Maintenance Practice)

Final Practice Exam Test

  

 

1. An aircraft should not be refueled when ?
   1.   the APU is running
   2.   navigation and landing light in operation
   3.   within 10 metres (30 feet) of radar operating
2. A CO2 extinguisher is used on ?
   1.   solid, liquid, hot metal and electrical fires
   2.   solid, liquid and electrical fires
   3.   solid and liquid fires
3. Which type of extinguisher can be used for engine fire ?
   1.   CO2
   2.   BCF
   3.   Water
4. Once a person has been disconnected from the source of an electrical shock the next step should be ?
   1.   seek assistance immediately
   2.   check for breathing start AR if necessary
   3.   check for pulse start cardiac massage if necessary
5. Water marks on bearings are indications of ?
   1.   bearing been run dry
   2.   bearing insufficiently lubricated
   3.   intergranular corrosion
6. For airworthiness purposes, aircraft structural parts are graded as ?
   1.   1, 2 and 3
   2.   class A, B and C
   3.   primary, secondary and tertiary
7. Dye penetrant kits should be stored ?
   1.   in direct sunlight to keep it dry
   2.   out of sunlight in a dry place
   3.   in a dark damp cupboard
8. If the aircraft is away from base who may certify the second part of the duplicate inspection ?
   1.   any licensed engineer
   2.   a pilot with a licence for any similar aircraft type
   3.   a pilot with a licence for the aircraft type
9. What colour is used to identify a 'primary structure' when using the aircraft Maintenance Manual ?
   1.   Red
   2.   Yellow
   3.   Green
10. How many primary bonding conductors are required on an engine ?
    1.   1 only
    2.   2 on one side
    3.   1 on each side
11. A lightning strike on an aircraft would show ?
    1.   the entry and exit point
    2.   the entry point only
    3.   the exit point only
12. After a heavy landing you should check ?
    
    1.   engine module alignment
    2.   engine compressor shaft alignment
    3.   engine thrust alignment
13. Skin wrinkling on the lower surface of a wing is caused by ?
    aircraft will
    
    1.   tension
    2.   hogging
    3.   sagging
14. The angle between starts on a double start thread is ?
    1.   120 degrees
    2.   180 degrees
    3.   90 degrees
15. How do you prevent earth loops forming on screened cables?
    1.   Earth one end of the screen
    2.   Earth both ends of the screen
    3.   Do not earth the screen
16. Spot facing is done to ?
    
    1.   provide a good surface for welding
    2.   compensate for height in lieu of a spring washer
    3.   provide a flat area on a rough surface
17. A jury strut is one giving?
    1.   a part of the structure that takes only tensile loads
    2.   a temporary support
    3.   additional support to a stressed area
18. Hi-loks are installed with the ?
    
    1.   thread and shank not lubricated
    2.   shank lubricated when fitting
    3.   thread lubricated when fitting
19. What type of rivet would you use when there is access to only one side of the work ?
    
    1.   Hilok
    2.   Pop
    3.   Blind
20. The maximum temperature for Nyloc nuts is ?
    
    1.   120°C
    2.   Pop
    3.   Blind
21. What NDT would you carry out on aluminium alloy ?
    
    1.   Electroflux
    2.   Magnetic flaw
    3.   Ultrasonic
22. To check the structure of a wing, which NDT is used ?
    
    1.   Magnetic Flaw
    2.   Dye penetrant
    3.   Radiographic
23. Which of the following NDT methods requires that the surface of the test piece is cleaned down to bare metal ?
    1.   Dye-penetrant
    2.   Magnetic Particle
    3.   Eddy Current
24. The fluid used in the 'Oil and Chalk' method of non-destructive testing is a mixture of ?
    1.   lubricating oil and lard oil
    2.   lubricating oil and paraffin
    3.   lubricating oil and petrol
25. What is an isotope the power source of ?
    1.   Gamma Rays
    2.   Ultra Violet Rays
    3.   X-Rays
26. Vapour phase inhibitor should be used ?
    1.   when degreasing a component
    2.   when re-protecting after corrosion
    3.   when painting an aircraft
27. What is used on magnesium to remove corrosion ?
    1.   Strontium chromate
    2.   Selenious acid
    3.   Chromic acid / sulphuric acid solution
28. Dents in a tubular push-pull rod are not allowed ?
    1.   in the end thirds of the rod
    2.   in the middle third of the rod
    3.   anywhere on the rod
29. What is used on Magnesium to re-protect it ?
    1.   Chromic Acid
    2.   Deoxidine
    3.   Selenious Acid
30. Taper pins are used in which of the following applications ?
    1.   To take compression loads
    2.   To take shear loads
    3.   To take compression and shear loads
31. What test do you do on a bonded join?
    1.   Peel
    2.   Shear
    3.   Tension
32. De-icing fluid Type 1 is used ?
    1.   where holdover times are long
    2.   where the ambient temperature is below -10degrees Centigrade
    3.   for short holdover times
33. When an aircraft is pulled out of soft ground, the equipment should be attached to ?
    1.   the tail cone
    2.   the main gear
    3.   the nose gear
34. An aircraft should be cleared of snow ?
    1.   using air blast
    2.   using hot fluid
    3.   using cold fluid
35. When weighing an aircraft, the hydraulic system should be ?
    1.   filled to 'maximum level' mark
    2.   completely full
    3.   empty
36. When weighing an aircraft, the hydrostatic weighing units are positioned ?
    1.   either under or on top of each jack
    2.   one under each jack
    3.   one on top of each jack
37. Aircraft measurements aft of the datum are ?
    1.   Either positive or negative
    2.   Positive
    3.   Negative
38. The flux used during brazing is a mixture of water and ?
    1.   zinc chloride
    2.   hydrochloric acid
    3.   borax powder
39. Brazing material is made from ?
    1.   copper and tin and lead
    2.   copper zinc and silver
    3.   copper, silver and tin
40. The materials most commonly soldered in soft soldering are ?
    1.   aluminium and magnesium
    2.   copper zinc and silver
    3.   copper, silver and tin
41. Silver solder melts within the range ?
    1.   200°C - 400°C
    2.   600°C - 850°C
    3.   400°C - 550°C
42. A flux is used in soldering to ?
    1.   etch the metal surface for more adhesion
    2.   dissolve oxides
    3.   prevent solder spikes
43. Plumbers solder is grade ?
    1.   B
    2.   C
    3.   D
44. Before soldering stainless steel it must be ?
    1.   Pickled
    2.   Cleaned with emery cloth
    3.   Sand papered
45. In a composite repair lay-up, how much should each layer extend beyond the layer below it ?
    1.   3 - 4 inches
    2.   2 - 3 inches
    3.   1 - 2 inches
46. Marking out on stainless steel can be clarified by application of ?
    1.   copper sulphate
    2.   sal ammoniac
    3.   ammonia
47. A hole drilled at the intersection of two bends in a fabricated sheet metal component is called ?
    1.   a drain hole
    2.   a crack stopper
    3.   a relief hole
48. The formula for setback for a 90° bend is ?
    1.   (½R + T)
    2.   (R + T)
    3.   (R + ½T)
49. The skin on an aircraft is normally manufactured from ?
    1.   2024 aluminium alloy
    2.   7075 aluminium alloy
    3.   2117 aluminium alloy
50. A cable should be replaced when individual wires are worn greater than ?
    1.   40%
    2.   60%
    3.   20%
51. HTS aircraft control cables are protected from corrosion by ?
    1.   zinc plating
    2.   cadmium coating
    3.   Galvanising
52. How would you use a Pacific T5 tensiometer ?
    1.   Use correct chart and correct riser
    2.   Use a standard riser and use the chart to correct for different sized cables
    3.   Use a load meter to apply the correct load
53. Backlash is a type of wear associated with ?
    1.   bearings
    2.   rivets
    3.   gears
54. Ball and roller bearings are made from a combination of low carbon steel and a percentage of ?
    1.   Nickel
    2.   Nickel chrome
    3.   Chromium
55. The international marking for a breathing oxygen pipe line is a series of ?
    1.   Rectangles
    2.   Diamonds
    3.   Dots
56. The international marking for a fire protection pipe line is a series of ?
    1.   circles
    2.   squares
    3.   diamonds
57. When carrying out a pressure test on a pipe it should be ?
    1.   twice the working pressure for two minutes
    2.   three times the working pressure for five minutes
    3.   1.5 times the working pressure
58. The minimum rivet pitch is ?
    1.   2 * the rivet diameter
    2.   3 * the rivet diameter
    3.   2 1/2 * the rivet diameter
59. What is the approximate distance of the sphere of influence of a rivet ?
    1.   5 D
    2.   2 D
    3.   4 D
60. Avdel rivets are closed by ?
    1.   A tapered mandrel
    2.   A broaching process
    3.   A squeezing process
61. In British rivets (solid) what is the length grading unit ?
    1.   1/16
    2.   1/32
    3.   1/10
62. 1EF6B22 NMSV What does the B mean?
    1.   Circuit function
    2.   Cable number
    3.   Segment letter
63. E' on a wire, under ATA 100 is a ?
    1.   phase indication
    2.   system ID code
    3.   cable size
64. The minimum distance between electrical cable splices is ?
    1.   500 mm
    2.   12 inches
    3.   3 feet
65. The pressure of the insulation crimp jaws on the PIDG crimping tool can be changed by ?
    1.   changing the position of the pins
    2.   using different coloured crimping pliers and terminations
    3.   varying the torque applied to the handles
66. To find a high resistance or open circuit, carry out ?
    1.   a milli-volt drop test
    2.   a continuity check
    3.   a bonding check
67. How long should a fireproof cable last in a fire ?
    1.   5 minutes
    2.   50 minutes
    3.   15 minutes
68. What gauge of pin would a yellow plastic insert/extract tool be used on ?
    1.   22 - 18
    2.   16 - 14
    3.   12 - 10
69. The length of a blended repair of corrosion should be no less than ?
    1.   5 times its depth
    2.   10 times its depth
    3.   20 times its depth
70. Which of the following is checked when using a 'GO / NO -GO' gauge ?
    1.   Clearance
    2.   Tolerance
    3.   Allowance
71. The maximum permissible bow in a steel tube is ?
    1.   1 : 400
    2.   1 : 200
    3.   1 : 600
72. NTS on a drawing stands for ?
    1.   Not To Scale
    2.   Not True Scale
    3.   No Tolerance System
73. The British Standard for Engineering Drawings is ?
    1.   BS 308
    2.   BS 306
    3.   BS 307
74. The maximum value of bonding of a secondary structure is ?
    1.   1 megohm
    2.   1 ohm
    3.   1 kilohm
75. A pyrometer is a ?
    1.   thermometer for use at high temperature
    2.   pyramid shaped altimeter
    3.   foam/granule fire extinguisher
76. On a long coaxial cable how would you check for discontinuities and shorts in situ ?
    1.   Continuity tester
    2.   Safety ohmmeter
    3.   Time Domain Reflectometer
77. The pitch of a hacksaw blade is?
    1.   the number of teeth on the blade
    2.   its length
    3.   the number of teeth per inch
78. What is the clearance angle on a normal twist drill ?
    1.   59 degrees
    2.   12 degrees
    3.   130 degrees
79. A rivet shaver is used to ?
    1.   Mill the tail after setting
    2.   Mill the tail after cutting
    3.   Mill the head flush
80. What temperature should the heat gun be set for shrinking heat shrink sleeve ?
    1.   100°C above rated temperature
    2.   100°C below rated temperature
    3.   At the rated temperature

Read More