M6 Materials Hardware Quiz: 10 Randomly Generated Questions from a (70-Question Bank)

 

 

Module - 06 (Materials & Hardware)

Quiz

 

1. What temperature would steel be tempered at?
   1.   At the annealing temperature
   2.   Above the annealing temperature
   3.   Below the annealing temperature
2. At normal temperatures HC steel is harder because?
   1.   it has more austenite
   2.   of the % of carbon in the granules
   3.   it has less austenite
3. Nitriding is ?
   1.   case hardening
   2.   anodising
   3.   tempering
4. The annealing process on steel is required sometimes as it ?
   1.   provides a corrosion resistant layer that prevents oxidation
   2.   relieves internal stress suffered after engineering processes
   3.   allows the material a greater stress per unit area
5. The properties of pearlitic metal are that it is both ?
   1.   strong but too and hard and brittle
   2.   soft and weak
   3.   strong without being brittle
6. The socket section of an AN/MS connector is normally installed on ?
   1.   either side of a circuit (makes no difference)
   2.   the ground side of the circuit
   3.   the power supply side of the circuit
7. When installing coaxial cable, it should be secured along its entire length ?
   1.   at 1-foot intervals
   2.   at 2-foot intervals
   3.   wherever the cable sags
8. When buffing surface of Aluminium Alloy, what material are you removing?
   1.   Oxide layer
   2.   Aluminium
   3.   Alloy
9. Why are aluminium alloys used on aircraft, instead of pure aluminium?
   1.   Lighter
   2.   Corrosion resistant
   3.   Stronger
10. The process of forming a pure layer of aluminium over an aluminium alloy is ?
    1.   cladding
    2.   electroplating
    3.   metalizing
11. Cast iron is ?
    1.   very malleable
    2.   tough
    3.   heavy and brittle
12. What is a Rockwell tester used for ?
    
    
    1.   Tensile Testing
    2.   Hardness Testing
    3.   Fatigue Testing
13. The symbol 'W' on a material indicates ?
    1.   it is for use on aircraft mainplanes only
    2.   it has been solution treated and will respond effectively to precipitation treatment
    3.   it is for workshop use only
14. Composition of silver solder is ?
    1.   tin, lead, silver and antimony
    2.   tin, lead and silver
    3.   tin and lead
15. Precipitation treating makes the metal ?
    
    1.   Precipitation treating makes the metal
    2.   less strong and hard
    3.   harder, stronger and less ductile
16. The time between removal from heat treatment furnace and quenching must be not more than ?
    1.   05 seconds
    2.   10 seconds
    3.   15 seconds
17. The metal which must not be heated in a salt bath is?
    
    1.   magnesium alloy
    2.   duralumin
    3.   rivets made of alclad
18. A material containing approximately 66% nickel and 33% copper is known as ?
    1.   Nimonic
    2.   Invar
    3.   Monel metal
19. Hooke's law states that, within the elastic region, elastic strain is?
    
    1.   directly proportional to stress
    2.   directly opposite to stress
    3.   indirectly proportional to stress
20. What type of a test involves stretching material until it breaks ?
    
    1.   Fatigue Testing
    2.   Hardness Testing
    3.   Tensile Testing
21. Two parts of the adhesive process are?
    
    1.   wetting and gripping
    2.   wetting and setting
    3.   spreading and setting
22. Polyester resin and glass fibre cloth, becomes ?
    
    1.   PTFE
    2.   PVC
    3.   GRP
23. A category of plastic material that is capable of softening or flowing when reheated is described as a ?
    
    1.   thermoset
    2.   thermoplastic
    3.   thermocure
24. The classification of high tensile strength fibreglass used in aircraft structures is ?
    
    1.   G-glass
    2.   E-glass
    3.   S-glass
25. Which of the following are generally characteristic of aramid fibre (Kevlar) composites ?
    1.   High tensile strength, stiffness and ability to conduct electricity
    2.   Flexibility, stiffness and corrosive effect in contact with aluminium
    3.   High tensile strength and flexibility
26. What tests are done on adhesive joints ?
    1.   Impact and peel
    2.   Shear and peel
    3.   Impact and shear
27. If you increase the amount of catalyst in a resin mixture ?
    1.   the pot life will be decreased
    2.   the material will become weaker
    3.   the material will become stronger
28. What is the largest hole in honeycomb repairable with microballoons ?
    1.   2.54 inches
    2.   2.54 mm
    3.   2.54 cm
29. What does MSDS stand for ?
    1.   Metal Surface Dimension Sector
    2.   Material Safety Data Sheet
    3.   Maximum Structural Design System
30. With what would you check the bonded joints of a wooden aircraft structure ?
    
    1.   A screwdriver
    2.   A plastic strip
    3.   A feeler gauge
31. Replacement of a wooden spar is ?
    1.   only permitted by the manufacturer
    2.   a minor repair
    3.   a major repair
32. A surface patch to a plywood structure may be a large as ?
    1.   50 inch perimeter
    2.   50 inch diameter
    3.   50 sq.inch area
33. The standard wood type for aircraft wood structures is ?
    1.   douglas fir
    2.   spruce
    3.   pine
34. Red heart and purple heart ?
    1.   are harmless natural defects in wood
    2.   are types of hard-wood
    3.   are forms of decay in wood
35. A faint line running across the grain of a wood spar generally indicates ?
    1.   shear failure
    2.   compression failure
    3.   decay
36. Lacing cord used on aircraft fabric covering must have a minimum breaking strength of ?
    1.   40 lb
    2.   80 lb
    3.   120 lb
37. Aircraft fabric lacing cord is reinforced with ?
    1.   lanolin
    2.   epoxy
    3.   wax
38. Which of the following is true regarding aircraft dope type ?
    1.   Either type of dope may be applied over the top of any type of dope
    2.   Butyrate dope may be applied over the top of nitrate dope
    3.   Nitrate dope may be applied over the top of butyrate dope
39. A retarder is added to aircraft dope to ?
    1.   produce a smoother finish
    2.   to retard the application time
    3.   to extend the shelf life
40. What width of finishing tape should be used on a tear in a fabric cover which is 10 inches long ?
    1.   4 inches
    2.   6 inches
    3.   2 inches
41. The threads per inch of Grade 'A' aircraft fabric is ?
    1.   60-64
    2.   110-115
    3.   80-84
42. Corrosion caused by electrolytic action is the result of ?
    1.   excessive anodization
    2.   contact between two unlike metals
    3.   the wrong quenching agent
43. Exfoliation corrosion is sometimes referred to as ?
    1.   sub-surface corrosion
    2.   filiform corrosion
    3.   layer corrosion
44. Which is the following correct statement ?
    1.   Selenious acid is used for the re-protection of aluminium alloys
    2.   The chemical test for bronze is nitric acid which produces a white precipitate
    3.   All corrosion is a chemical action
45. Corrosion control begins at the ?
    1.   production stage
    2.   manufacturing stage
    3.   design stage
46. Corrosion caused by galvanic action is the result of ?
    1.   excessive anodization
    2.   contact between two unlike metals
    3.   excessive etching
47. What are the signs of fretting corrosion ?
    1.   Black powder or cocoa staining
    2.   Intergranular cracking
    3.   Flaking
48. Magnesium alloy components are protected by ?
    1.   an electro process
    2.   a chemical process
    3.   a painted process
49. Corrosion at the grain boundaries is called ?
    1.   filiform
    2.   fretting
    3.   intergrannular
50. Anti-corrosion treatment used on Magnesium is ?
    1.   chromating
    2.   electro-plating
    3.   phosphating
51. The pitch of a screw thread is ?
    1.   2 * crest to root
    2.   crest to root
    3.   crest to crest
52. A metric screw thread angle is ?
    1.   37 °
    2.   57 °
    3.   60 °
53. What sort of surface treatment would you find on a magnesium casting ?
    1.   Chromating
    2.   Phosphating
    3.   Anodizing
54. Studs which have a size larger thread at one end are called ?
    1.   plain studs
    2.   shouldered studs
    3.   stepped studs
55. A dowel will take what loads ?
    1.   torsion
    2.   tensile
    3.   shear
56. UNF means ?
    1.   union national fine
    2.   unified fine
    3.   united nations fine
57. Aircraft bolts are usually manufactured with a ?
    1.   class 3 fit for the threads
    2.   by itself
    3.   with a plain washer
58. A spring type washer when used on an aluminium component must be used ?
    1.   with a tab washer
    2.   by itself
    3.   with a plain washer
59. Taper pins are subject to what loads ?
    1.   Shear
    2.   Compressive
    3.   Tensile
60. How is a British aluminium rivet identified ?
    1.   Violet anodic finish
    2.   Natural anodised finish
    3.   Black anodic finish
61. An aluminium alloy L37 rivet identification is ?
    1.   D embossed
    2.   O embossed
    3.   X embossed
62. The length of solid rivets is in graduations of ?
    1.   1/4 inch
    2.   1/8 inch
    3.   1/16 inch
63. Countersunk rivets have two angles of countersink, these are ?
    1.   100 - 115 degrees
    2.   125 - 135 degrees
    3.   100 -160 degrees
64. A 'HUCK' rivet is similar in design to a ?
    1.   dome head rivet
    2.   blind rivet
    3.   cherry rivet
65. What type loads cause the most rivet failures ?
    1.   Bearing
    2.   Head
    3.   Shear
66. How are flexible hoses categorised ?
    1.   By diameter
    2.   By maximum pressure
    3.   By length
67. How would you test a hydraulic hose ?
    1.   Pressure test 1.5 * working pressure
    2.   Pressure test 2.0 * working pressure
    3.   Pressure test 1.0 * working pressure
68. Which material is a hydraulic fluid hose made from ?
    1.   Rubber
    2.   Butyl
    3.   Teflon
69. A 0.5 in. diameter pipe is to be joined using standard nuts and fittings. What coupling would you use ?
    1.   AN8-8852-2
    2.   AN8-8852-8
    3.   AN8-8852-1
70. A self aligning bearing is a ?
    1.   angular bearing
    2.   precision bearing
    3.   radial bearing
71. What type of gear would be used on a propeller reduction gearbox ?
    1.   Bevel
    2.   Epicyclic
    3.   Split epicyclic

Read More